Geothermal Heating Installation in Everett

At Everett Geothermal Heating, we have years of experience installing complete ground-source heating and cooling systems for homeowners. Our professionals are reliable, we know heating, and our work is guaranteed. Call us today for a free, personalized quote, no obligation.

A geothermal system pairs an indoor heat pump with a loop of pipe buried in the ground. We design each system around your land, drilling access and the home’s heating load. We compare vertical bores with horizontal loops before choosing equipment, and we check the existing ductwork, radiant floors and electrical capacity. Scroll down to learn more about geothermal heating and how we work.

Contemporary home with a garden and a ground-source heating unit in a side utility room
Vertical geothermal loop installationHorizontal geothermal loop installationGeothermal heating retrofitGeothermal radiant floor heatingGeothermal installation for new homes

Residential geothermal heating and cooling installation

Parked drilling rig and coiled ground-loop pipe beside a houseLong trench across a back lawn with black ground-loop pipe laid in loops, soil piles and a small parked excavator by the house

Vertical geothermal loop installation

Vertical bores need far less yard than trenches, but the drill rig still has to get in. Before we lay out the bores, we walk the site for rig access, buried utilities and the ground. How deep and how far apart they go depends on the home’s heating load.

Horizontal geothermal loop installation

A horizontal loop is pipe laid in trenches across open ground. Usable yard, buried utilities, room for the digger and future landscaping all shape the layout. Before we choose the loop, we go over the digging, how the pipe reaches the house, how the yard is put back and how we record where it is buried.

Indoor ground-source heat pump with insulated pipes and air-distribution ductwork

Geothermal heating retrofit

We size a replacement from the home’s heat loss and its ducts or pipes rather than the old furnace or boiler. We inspect the ducts or hot-water circuits, the electrical panel and the room for the indoor unit, then time the changeover so the loop, controls and indoor work are ready in the right order.

Geothermal radiant floor heating

A geothermal heat pump that heats water can run radiant floors, as long as the floor build-up and the water temperature suit it. We work out each room’s heat loss, then lay out the tubing and controls to match. We plan cooling and hot water separately.

New two-story house in framing and house wrap with black ground-loop pipes trenched to the foundation

Geothermal installation for new homes

On a new build we can place the loop and the indoor equipment before the foundation, utility lines and landscaping close off the routes. We reserve space for the equipment, fit the loop work into the construction schedule and size the system from the planned insulation and room loads, then test it and show you how it runs.

Geothermal heating costs

These ranges cover the ground loop, the geothermal heat pump and hired labor for typical homes in Everett and nearby towns. The low end is for an open, easy site and a simple system. The top end is for deeper bores, rock, tight access, duct changes or electrical upgrades. The final size comes from a heat loss calculation for your house, not from floor area alone.

Vertical geothermal loop installation

  • Home up to about 2,000 sq ft (about 3 tons)$25,500 – $40,500+
  • Home about 2,000 to 2,500 sq ft (about 4 tons)$27,500 – $52,000+
  • Larger home, about 3,000 sq ft (about 5 tons)$41,000 – $72,000+
What is included

Drilling the vertical bores, setting and grouting the loop pipe, piping it to the house, and the geothermal heat pump connected and started up. The driller files a notice with Washington Ecology before drilling. Duct changes are extra.

Get a free quoteSee an example projectAbout this service

Horizontal geothermal loop installation

  • Home up to about 2,000 sq ft (about 3 tons)$21,500 – $34,000+
  • Home about 2,000 to 2,500 sq ft (about 4 tons)$23,000 – $44,000+
What is included

Digging the trenches, laying and pressure testing the loop pipe, backfilling, and the geothermal heat pump connected and started up. Yard repair after the trenching is usually extra.

Get a free quoteSee an example projectAbout this service

Geothermal heating retrofit

  • Existing home up to about 2,000 sq ft (about 3 tons)$23,000 – $41,000+
  • Existing home about 2,000 to 2,500 sq ft (about 4 tons)$25,000 – $51,000+
What is included

Taking out the old furnace or boiler, the ground loop and geothermal heat pump, changes to the existing ducts where needed, start-up and testing.

Get a free quoteSee an example projectAbout this service

Geothermal radiant floor heating

  • Floor tubing for about 1,000 sq ft, new floor or slab$7,500 – $15,000+
  • Floor tubing for about 1,000 sq ft, existing floors$12,500 – $25,500+
  • New home about 2,000 sq ft: ground loop, heat pump and floor heating$30,000 – $65,000+
What is included

Floor heating tubing, manifolds and controls, connected to a geothermal heat pump that heats water. The whole-system line also includes the ground loop.

Get a free quoteSee an example projectAbout this service

Geothermal installation for new homes

  • New home up to about 2,000 sq ft (about 3 tons)$15,000 – $34,000+
  • New home about 2,000 to 2,500 sq ft (about 4 tons)$16,000 – $44,000+
What is included

The ground loop and heat pump planned with the house, put in while the site is open, and connected to the new ducts or floor heating.

Get a free quoteSee an example projectAbout this service

Ranges are 2026 estimates, not quotes. Call today for a free, personalized quote.

Our process

01

House and land check

We look at the house and the land, work out the heating and cooling loads and see where a loop can go.

02

Loop and indoor design

We match the loop to the indoor unit, the ducts or floor and the electrical work, and check the site and drilling rules.

03

Install, test and record

We install and test the system, finish the agreed yard work, and leave you a drawing of the loop and notes on the controls.

Lot size is only the starting point

How much loop a yard can take depends on access, buried utilities, setbacks and the ground itself, not just the size of the lot. Show us a site plan and mention any additions or landscaping you have in mind, so the loop stays clear of them. We walk the yard on the first visit.

Drilling notices and local permits

Before any work starts, we confirm the current drilling requirements, including the Washington Ecology notice, and which local site, mechanical and electrical permits your address needs.

Geothermal heating installation in Everett and nearby communities

We work in Everett and also take projects in Snohomish and Monroe. Call us with your address and we will confirm we can come out.

Frequently asked questions

Is geothermal heating the same as an air-source heat pump?

Both use electricity to move heat. A ground-source system trades heat with the ground through a buried loop instead of with the outside air, so it needs drilling or trenching and more design work.

Can geothermal provide cooling too?

Many ground-source systems heat and cool. With ducts, the heat pump can blow cool air through the house in summer. A radiant floor on its own does not cool the house or take out humidity.

Can you size the system from my floor area?

Only as a first guess. We size the system from a heating and cooling load calculation for the house, together with the loop design and the ducts or floors it feeds.

Request a free geothermal heating quote

We recommend calling us, but feel free to use this form to contact us. We'll get back to you with a full, personalized quote or additional questions as soon as possible.

Call (425) 212-1157

Call (425) 212-1157